Xylem IMS SOLOQ 1 Aquavar SOLO Quick Installation Guide User Manual download pdf

Aquavar SOLO – Quick Installation Guide

1. Mount Aquavar SOLO Drive (in a vertical position);

• Must have 6” minimum clearance on all sides for proper cooling.

2. Wire Input Power to SOLO Drive (Single Phase, 230V)

• Review Circuit Breaker Sizing - see IMS-SOLOQ-2 or IM229

3. Wire Motor Drop Cable to SOLO Drive (75˚C Copper Wire min.)

• 3AS Models - Use with Three Phase, 230V, ¾ to 5 HP Motors

• 1AS15 Model - Compatible w/Single Phase, 230V Motors

❍

3-Wire - .5 - 2 HP CP / Pentek XE; .5 – 1.5 HP FE & Grundfos

❍

2-Wire - .5 – 1.5 CentriPro, Pentek XE, Franklin Elec. & Grundfos 2-Wire

– units with R05K or newer software only.

• Review Wire Sizing (Table 4 of IM229)

4. Mount Transducer and Conﬁrm Transducer Cable Wiring

• Transducer cable maximum length = 200 feet

• Connect Pressure Transducer to piping manifold and to ground

5. User Interface Board Adjustments

• Select proper “Current Limit Setting” (equal to motor SFA)

• 1AS15 Only - Set “Pump Stop Sensitivity” - High is Default

• 3AS

_ _

Only - Select maximum frequency setting (60 Hz or 80 Hz);

❍

60 Hz = matching Liquid End HP and Motor HP

❍

80 Hz = “over-speed” application; motor HP > Liquid End HP

• Dry Well Sensitivity - Set on “High” position;

❍

If nuisance tripping occurs, switch to “Low” position

• Low Pressure Cut-Off and Pressure Drop setting adjusted to application /

system requirements.

• Optional use of Secondary Switch Connection, refer to IM229

6. Adjust Tank Pressure

• Set approximately 20 PSI below pressure set point

• Adjust as needed to optimize - see IMS-SOLOQ-2 or IM229

7. Turn Drive Power On - Adjust Pressure - Purge Air

• Purge air from system and check for leaks

• Factory default is 50 psi - push and hold Increase Pressure button if

higher pressure is desired and also adjust tank pre-charge.

8. Check Motor Rotation and Conﬁrm Performance

Refer to Aquavar SOLO Installation Manual, IM229, for complete details.

Check Motor Insulation Resistance on retrot jobs before replacing drive.

QUICK START GUIDE

IMS-SOLOQ-1

1 2 3 4 5 6

Summary of Contents

Page 1 - QUICK START GUIDE

Aquavar SOLO – Quick Installation Guide 1. Mount Aquavar SOLO Drive (in a vertical position); • Must have 6” minimum clearance on all sides for prope

Page 2 - Xylem Inc

1AS Controllers 3AS ControllersPressure Ranges for All Available Transducers Transducer 1AS15 / 3AS20 3AS30 3AS50 (Min. PSI) (Max. PSI) (Min.

Page 3 - SOLO Controller

Aquavar® SOLO ControllerPRESSURE TANK SIZING and SET-UP• Use Total Tank Volume to size tank. Total tank volume should be approximately 20% of the pump

Page 4 - FAULT CODES

FAULT CODESNo Light: Low Voltage or No Voltage to ControllerGreen Light Codes:• Constant Green - Unit in Standby: system is Off or system det

Page 5

Aquavar SOLO – Quick Installation GuideRecommended 1AS15 Overload Settings - All Motor Brands Motor HP Brand Motor No. Set Dial Type SFA Wi

Page 6 - VFD Accessories

Comments to this Manuals

No comments

Xylem IMS SOLOQ 1 Aquavar SOLO Quick Installation Guide User Manual

Browse online or download User Manual for Pumps Xylem IMS SOLOQ 1 Aquavar SOLO Quick Installation Guide. Xylem IMS SOLOQ 1 Aquavar SOLO Quick Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Pumps Xylem IMS SOLOQ 1 Aquavar SOLO Quick Installation Guide