Xylem II 231 P INSIDER User Manual download pdf

The PumpSaver

Plus Model 231-P-INSIDER fits inside 1/3 – 1hp, 230V Franklin™, Pentek™, or

CentriPro™ control boxes. PumpSavers are designed to protect single-phase pumps from dry-well,

dead-head, rapid-cycling, jammed impeller, and over/undervoltage conditions. Typical applications

include residential waterwells, commercial waterwells, irrigation wells, and golf course and other

sprinkler systems.

CONNECTIONS

Refer to specific connection instructions depending on the particular control box being used:

Franklin™ control box – page 3

Pentek™ control box – page 5

CentriPro™ control box – page 7

CALIBRATION / SETTINGS

1. Turn RESTART DELAY/C ALIBRATION to the CAL position and close the box cover.

2. Apply power to the system. The pump should run for approximately 10 seconds and then shut

off—this indicates the Model 231-P INSIDER has calibrated.

3. Remove power from the system. Open the control box and set the appropriate dry-well recovery

time with the RESTART DELAY / CALIBRATION knob.

4. Shut the control box and re-apply power to the system.

OPERATION

The Model 231-P-INSIDER monitors pump load in amps and kilowatts. When the current (amps)

exceeds approximately 125% of calibrated current, or power (kW) drops below the adjustable

underload trip point, the 231-P-INSIDER—after the trip delay—will turn off the pump. The 231-P-

INSIDER will automatically restart the pump after the selected restart delay time.

The calibration is stored in permanent memory. The PumpSaver

Plus does not need to be

recalibrated if power is lost.

SENSITIVITY

The Model 231-P-INSIDER has an adjustment knob to set the underload trip sensitivity. Setting

SENSITIVITY to the middle position (straight up) is equivalent to SymCom’s standard underload

trip level. Adjust the SENSITIVITY knob to increase/decrease underload sensitivity up to

approximately ±10% of the standard trip. It may be necessary to increase the sensitivity if the

PumpSaver

Plus does not trip on dry-run or dead-head or it is known that the water level in the

well is very low relative to the pumps capabilities.

WARNING: Decreasing the SENSITIVITY may compromise the PumpSaver’s ability to

detect dry-run and/or dead-head conditions.

2880 North Plaza Drive, Rapid City, SD 57702

(800) 843-8848 · (605) 348-5580

www.symcom.com

INSTALLATION INSTRUCTIONS FOR

SYMCOM MODEL

231-P-INSIDER

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - 231-P-INSIDER

The PumpSaver®Plus Model 231-P-INSIDER fits inside 1/3 – 1hp, 230V Franklin™, Pentek™, orCentriPro™ control boxes. PumpSavers are designed to protect

Page 2

104/07

Page 3 - FRANKLIN™ CONTROL BOX

114/07

Page 4

124/072880 North Plaza Drive, Rapid City, SD 57702(800) 843-8848 · (605) 348-5580www.symcom.comVisit us atwww.symcom.com to seeour complete product l

Page 5 - PENTEK™ CONTROL BOX

24/07RUN HOURSThe Model 231-P-INSIDER records pump run hours. Run hours can be displayed by aPumpSaver®Plus Informer (see USING AN INFORMER). Run hour

Page 6

34/07FRANKLIN™ CONTROL BOXCONNECTIONS1. Remove the cover from the front of the 3-wire Franklin™ control box.2. Remove the yellow wire from the term

Page 7 - CENTRIPRO™ CONTROL BOX

44/07FRANKLIN™ CONTROL BOXSOLID-STATESWITCHB(MAIN) Y(COMM)BLKREDORANGEYELR(START) L2 L1BLUE111/231INSIDERFigure 2: Franklin™ Control Box with the Mode

Page 8 - TROUBLESHOOTING

54/07PENTEK™ CONTROL BOXCONNECTIONS1. Remove the cover from the front of the 3-wire Pentek™ control box.2. Remove the yellow wire from the terminal

Page 9

64/07PENTEK™ CONTROL BOXFigure 4: Pentek™ Control Box with the Model 231-P-Insider Installed

Page 10

74/07CENTRIPRO™ CONTROL BOXCONNECTIONS1. Remove the cover from the front of the 3-wire CentriPro™ control box.2. Remove the yellow wire from the te

Page 11

84/07TROUBLESHOOTINGRUN LIGHT CAL LIGHT PROBLEM or FUNCTION CORRECTIVE ACTIONOn Steady OffRUN:Pump is running—or ready to run—noproblems in operation

Page 12 - youre looking for?

94/07SymCom warrants its standard products against defects in material or workmanship for a period offive (5) years from the date of manufacture excep

Comments to this Manuals

No comments

Xylem II 231 P INSIDER User Manual

Browse online or download User Manual for Pumps Xylem II 231 P INSIDER. Xylem II 231 P INSIDER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Pumps Xylem II 231 P INSIDER